SMD LED 2835 0.2W

Product Detail

? Feature


Viewing angle:120 deg                        

The materials of the LED dice is InGaN          

3.50mm×2.80mm×0.7mm                      

  RoHS compliant lead-free soldering compatible




? Package Outline      

Unit:mm






NOTES:  

1. All dimensions are in millimeters;   

2. Tolerances are±0.03mm unless otherwise noted.  







?Absolute maximum ratings                                            Ta=25±3?

Parameter	Symbol	Value	Unit
Power dissipation	Pd	0.2	W
Forward current	If	60	mA
Reverse voltage	Vr	5	V
Operating temperature range	Topr	-20~+85	?
Storage temperaturer range	Tstg	-40~+100	?
Pulse Forward Current	Ifp	180	mA
Electrostatic Discharge	ESD	2000(HBM)	V

 

?Electro-optical characteristics                                        Ta=25±3?

Parameter	Test Condition	Symbol	Value					Unit
			Min.	Typ.			Max.
Forward voltage	If=60 mA	Vf	2.7	--			3.0	V
Luminous intensity	If=60 mA	F	29	--			--	Lm
Viewing angle 50% Iv	If=60 mA	2? 1/2	--	120			--	Deg
Reverse current	Vr=5V	Ir	--	--			10	µA
ColorTemperature	If=60 mA	TC	--	3000			--	K
Chromaticity CIE	If=60 mA	CIE
CRI	If=60 mA	Ra	=80
NOTES:
1.Luminous Flux measurement tolerance:±10%
2.Forward Voltage measurement tolerance:±0.1V
3.Color Temperature measurement tolerance:x,y±0.01
4.CRI measurement tolerance:±2

 


? Typical optical characteristics curves 

 





? Intensity Bin Limit (IF = 60 mA)  

 

Bin code	Flux(lm) for reference
	Min	Max
1	29	30
2	30	31

 

 

? VF Bin Limit (IF = 60 mA)

 

Bin code	Min.(V)	Max.(V)
1	2.7	2.8
2	2.8	2.9
3	2.9	3.0

 

? Chromaticity CIE 









? Color Bin Limit (IF = 60 mA)








?Requirements for application and reflow soldering

 

Reflow Soldering
Pre-heat	120~160?
Pro-heat time	120 seconds Max.
Peak temperature	245? Max.
Soldering time	10 seconds Max.
Condition	Refer to Temperature-profile

 

After reflow soldering rapid cooling should be avoided

Temperature-profile(Surface of circuit board)  

Use the following conditions shown in the figure.    

 

 <Pb-free solder>                                           <Lead solder>



1.Reflow soldering should not be done more than two times    

2.When soldering,do not put stress on the LEDs during heating







?Handling Precautions

Compare to epoxy encapsulation that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more prone to damage by external mechanical force. As a result, Special handling precautions must be observed during assembling using silicone encapsulated LED product, Failure to comply might leads to damage and premature failure of the LED.

 

? Handle the component along the side surface by using forceps or appropriate tools; do not directly touch or handle the silicone lens surface, it may damage the internal circuitry.

 

? Not suitable to operate in acidic environment, PH<7.

 

? LED operating environment and sulfur element composition cannot be over 25 PPM in the LED mating usage material.

 

When we need to use external glue for LEDs application products, please make sure that the external gluematches the LEDs packaging glue. Additionally ,as most of LEDs packaging glue is silica gel, and it has strong Oxygen permeability as well as strong moisture permeability; in order to prevent external material from getting into the inside of LEDs, which may cause the malfunction of LEDs, the single content of Bromine 

element is required to be less than 225 PPM,the single content of Chlorine element is required to be less than225PPM,the total content of Bromine element and Chlorine element in the external glue of the applicationproducts is required to be less than  375 PPM.

 

? The encapsulated material of the LEDs is silicone. Therefore the LEDs have a soft surface on the top ofpackage. The pressure to the top surface will be influence to the reliability of the LEDs. Precautions should betaken to avoid the strong pressure on the encapsulated part. So when using the picking up nozzle, the pressureon the silicone resin should be proper.

 

? Static electricity or surge voltage damages the LEDs. Damaged LEDs will show some unusual characteristicssuch as the lower forward voltage, or the not light at low current, even not light. All devices, equipment andmachinery must be properly grounded. At the same time, it is recommended that wrist bands oranti-electrostatic gloves, anti-electrostatic containers be used when dealing with the LEDs.

 

Storage

? Before opening the package, the LEDs should be kept at 30? or less and 60%RH or less. The LEDs shouldbe used within a year.

 

? After opening the package, the product should be stored at 30? or less and humidity less than 10% RH, andbe soldered within 24 H. It is recommended that the product be operated at the workshop condition of 30?or less and humidity less than 60% RH. If unused LEDs remain, they should be stored in moisture proofpackages, such as sealed containers with packages of moisture absorbent material (silica gel). It is alsorecommended to return the LEDs to the original moisture proof bag and to reseal the moisture proof bagagain.




?Reliability

 TEST ITEMS AND RESULTS

Type	Test Item	Ref.Standard	Test Conditions	Note	Number of Damaged
Environmental Sequence	Resistance to Soldering Heat(Reflow Soldering)	JESD22-B106	Tsld=260?,5sec	2 times	0/100
	Temperature Cycle	JESD22-A104	-40?30min ??5min 100? 30min	100 cycle	0/100
	Thermal Shock	JESD22-A106	-40?15min ??5min 100? 15min	100 cycle	0/100
	High Temperature Storage	JESD22-A103	Ta=100?	1000 hrs	0/100
	Low Temperature Storage	JESD22-A119	Ta=-40?	1000 hrs	0/100
	Power temperature Cycling	JESD22-A105	On 5min -40?>15min ??    ??<15min Off5min 100?>15min	100 cycle	0/100
Operation Sequence	Life Test	JESD22-A108	Ta=25? IF=150mA	1000 hrs	0/100
	High Humidity Heat Life Test	JESD22-A101	80?RH=80% IF=150mA	1000 hrs	0/100

CRITERRIA FOR JUDGING THE DAMAGE

Item	Symbol	Test Conditions	Criteria for Judgement
			Min.	Max.
Forward Voltage	VF	IF=150mA	--	U.S.L*)×1.1
Reverse Current	IR	VR=5V	--	U.S.L*)×2.0
Luminous Intensity	IV	IF=150mA	L.S.L**)×0.7

U.S.L.:Upper Standard Level              L.S.L.:Lower Standard Level




All kind of  lights :



 

Packaging & Delivery

Packaging Details

4000pcs/reel, each reel Anti-static vacuum Bag




Delivery Time

Shipped in 3-5 days after payment




 



 

Cautions

1)Soldering Conditions

Number of reflow process shall be less than 2 times and cooling process to normal temperature is required between first and Second soldering process.




2)Static Electricity

It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs.All devices, equipment and machinery must be properly grounded.Damaged LEDs will show some unusual characteristics such as the forward voltage becomes lower, or the LEDs do not light at the low current. Criteria : (VF > 2.0V at IF=0.5mA) 




3)Moisture Proof Package

It is recommended that moisture proof package be used .




4)Storage

Before opening the package ,The LEDs should be kept at 30°C or less and 70%RH or less. The LEDs should be
used within a year.




5)After opening the package, The LEDs should be soldered within 24 hours (1days) after opening the package.




Company:








Patents:













Contact:

Alisa Huang

Guangdong Elite Optoelectronic Technology Co., LTD

Mobilephone:+86-18033336027

Tel:0769-89080660-824

Fax:0769-89080658

Email:ruilu_sales1@elitebm.com




Contact: Carol Chen

Mobilephone:+86-13798703095

Telephone:+86-769-88941998

Email:elite1@elitebm.com